| Matters related to the assembly and maintenance of the knitting machine. For some parts of the knitting machine, such as spindle support and sliding seat, the accurate distance between the sliding seat and the lower spindle braid must be ensured after maintenance and disassembly or replacement of new parts for reassembly. It is suggested to put a sliding frame and its upper spindle to run on the sliding rotary table first, so that the lower anchorage braid will not be hooked or cut off by the sliding frame when it is led from the swing rod to the braiding point. If the precise adjustment distance cannot be reached by moving one tooth, fine adjustment can be carried out according to the following steps: loosen the five fixing screws on the inner ring gear. Since the through hole is elliptical, fine adjustment of the sliding frame can be realized by moving the inner ring gear. Tighten the screws after adjustment in place. Place the remaining sliding frames evenly on the sliding ring track. If the swing height of the braided wire is different after the installation of the new swing rod, it shall be adjusted to all swing rods have the same stop point. 1、 Check whether the lubricating oil in the knitting machine case is within the specified range, pick up the oil probe rod and lower it to ensure that the oil volume is in the center of the two lines, but do not spray too much to avoid external spraying of lubricating oil; 2、 The lubricating oil of the turbine case of the knitting machine can be visually inspected by the oil mirror. When it is lower than half of the oil mirror, the lubricating oil needs to be supplemented. (when replenishing, it shall not be higher than the oil mirror); 3、 The impeller and shaft center of the knitting machine shall be lubricated and the table surface shall be wiped clean before starting each shift to avoid foreign matters from jamming the traveling ingot; 4、 All transmission gears of the knitting machine shall be properly lubricated and maintained; 5、 Proper lubrication and maintenance shall be carried out on the polished rod of the light sensing wire arranger of the knitting machine; 6、 There must be no obstacle within the action range of knitting machine; 7、 Tighten the screws at the transmission and connection parts of the knitting machine to avoid loosening and affecting the machine operation; 8、 Before operating the knitting machine, please run it at low speed for about 5 minutes before increasing the speed. During rough adjustment, place spindles on two adjacent external spindle supports, lead the braided wire to the braided point through the swing rod, and stack it tightly. When the braided wire enters or exits from the notch on the sliding turntable track, the distance from the braided wire to the edge of the upper spindle sliding frame must be basically equal. The adjustment of the distance can be achieved by changing one or more gears forward or backward of the gear carrier. If the precise adjustment distance cannot be reached by moving one tooth, fine adjustment can be carried out according to the following steps: loosen the five fixing screws on the inner ring gear. Since the through hole is elliptical, fine adjustment of the sliding frame can be realized by moving the inner ring gear. Tighten the screws after adjustment in place. Put the rest of the sliding frames evenly on the sliding ring track to introduce the matters related to the assembly and maintenance of the knitting machine. If the swing height of the braided wire is different after the installation of the new swing rod, it should be adjusted to all the swing rods have the same stop point. Guanbo knitting machine is generally composed of main machine and auxiliary machine. Through the cooperation of the main machine and auxiliary machine, simple patterns such as arc needle and Yuanbao needle can be woven. The auxiliary machine is mainly used to weave rib edge, which can make the fabric elastic. The jacquard function is completed in the main machine part. The loop collection, overhead and two-color jacquard can be realized by a row of needle plates separated by one, two and three and the needle starting triangular shift lever of the machine head, and the pattern weaving such as mesh weaving can be realized by wood needle transfer coil, or the needle methods such as arc needle, Yuanbao needle, Siping needle and double plate jacquard needle can be woven through the cooperation of front and rear needle beds, The front needle bed can also be operated independently to weave a variety of patterns such as ring collection, overhead, mesh and so on. |
